with Green Grabber® surfaces
and Xtra LED
Eliminate water changes. Remove nuisance algae, nitrate and phosphate. Cultivate seaweed for feeding.
Click the "image gallery" button above for more pictures
Similar DROP.6x installed on dirty freshwater tank:
Similar DROP.6x first cleaning on dirty freshwater tank:
Similar DROP1.4 installed on saltwater reef pond:
Comparison of all the DROP scrubbers:
DROP1.2x dimensions: 3.25" wide x 6" tall x 2.75" thick front-to-back (8 cm wide x 15 cm tall x 7 cm thick). It requires at least 5" (13 cm) of water to operate in.
Operates on both 120 and 240V. Can be shipped to any country; you can find shipping costs by putting the item into the shopping cart; be sure to click "display rates"
Get the no-overflow advantage of an upflow scrubber: since it is ALL underwater, it can't overflow onto your floor.
Finally an aquarium filter that offers drop-in installation in the smallest of spaces, along with reduction or elimination of water changes and nuisance algae. And it's small enough to drop into the back compartment of most all-in-one aquariums. It operates the way the oceans and lakes do, using algae to do all the filtering, and it truly can replace all other filters in your aquarium if sized and operated correctly. The DROP1.2x grows well in water with phosphate up to 0.5 ppm.
Strong injection-molded case! This DROP1.2x drop-in algae scrubber has 28 square inches (170 square cm) of extremely rough Green Grabber ® one-sided algal growth surface which can grow up to 1/2" (1 cm) thick green hair algae. This is designed to absorb the nutrients from this much feeding per day:
1.2 Frozen cubes, or
12 Pinches of flake, or
12 Square inches (72 square cm) of nori, or
0.12 dry ounce (3.6 grams) of pellets
The physical size or number of gallons or liters of water in your tank or sump does not matter; however the amount of problem rock you might have, does. If you have rocks which are soaked with phosphate from having been in a problem aquarium, each 10 pounds (4.5 kg) of this problem rock will add 0.2 cube a day to your feeding amounts; so be sure to account for this when choosing a scrubber size or number of scrubbers. For example if you feed 0.5 cube a day, but have 20 pounds of rock that came from a tank with nuisance algae problems, this rock will add 0.4 cubes a day to your feeding. This applies even if the rock was dried out and bleached, because this does not remove any nutrients from the rock.
If you feed more than the above amounts, you can get multiple DROP1.2x units; multiple units are preferred over one larger unit because you can clean one unit per week, and because you'll always have one unit filtering while the other one starts growing again after a cleaning. Multiple DROP1.2x units are also good for backup.
Click the "image gallery" button above for more pics, or click here:
The DROP1.2x will fit into any size aquarium, sump, and almost all back compartments of all-in-one aquariums. Nano and pico tanks, with sumps on the back side, normally have compartments at least 3" (15 cm) wide; and the DROP1.2x only need 3.5" width.. And of course it can fit into the display (the main part of the tank). The DROP1.2x has a special plate under it which allows it to sit on the bottom of your aquarium or sump, including sitting on sand; the plate not only keeps sand from getting into the filter, but also blocks most of the red light from coming out.
The DROP1.2x has water inlets and outlets at the bottom of the growth compartment, where internal upflowing air bubbles inside the unit (from an air pump which you provide) flow up into the growth compartment and bring aquarium water inside it. As the water enters the growth compartment, it mixes with the air bubbles, and rubs the algae-attachment Green Grabber textures, and gets blasted by the super-red 660nm LED light. This rubbing of bubbles causes algae to start growing on the rock hard (and heavy) Green Grabber textures; freshwater grows thin stringy algae, and saltwater grows thicker, denser algae. The air then goes out of the top of the unit, and the water goes down and out the bottom, without many air bubbles remaining.
The Green Grabber algal growth attachment surface is so rough and prickly that is might be the roughest thing you've ever felt. A cactus might be sharper, but that's about it. Rough surfaces are critical for allowing algae to attach and grow and thus provide strong absorption of nutrients. The rock-hard protrusions stick straight out 1 to 3 mm. Previous algae scrubber screens were made from "slippery" plastic canvas that is used for sewing and knitting; algae take a long time to attach to it. Green Grabber growth surfaces are not plastic at all; instead they are rock hard and have jagged rough edges and points (don't let children play with them). And the white color of the Green-Grabber surface reflects as much light as possible, allowing lots of light to reflect back to the algae. Light = photosynthesis = filtering.
The main advantage of the DROP1.2x or any algae scrubber is that if you size and operate it properly (based on how much you feed), it can be the only filter for your tank, even replacing waterchanges. It can, however, also be used with other filters. Some other filters such as carbon dosing (Zeo, pellets, etc) may slow down the scrubber, but nothing will really "hurt" the scrubber except possibly large amounts of algaecide or copper medications. The DROP1.2x is also dry-out proof, since it's always under water. Power outages will not affect it.
The DROP1.2x will run on both 120V and 240V, and comes with a 10 ft (300 cm) UL and CE approved power adapter cord with a U.S. plug. If you require a different plug you can get an adapter at any local hardware or travel store, or online, or you can cut off the U.S. plug and install your own plug from a hardware store. It is a simple 2-wire plug, which is also the same as a laptop power supply cord. The power cord is actually the same as a laptop computer cord with a C7 connector (looks like a figure eight), so you can swap your laptop cord with your DROP if you want to.
The DROP1.2x uses a low voltage that is perfectly safe. The LEDs are sealed in a double waterproofed manner; this prevents corrosion from fresh and saltwater. The UL and CE approved power supply works on both 120 or 220 volts, it converts (and isolates) the 120 or 220 volt mains to the safe low voltage which is isolated from the water, meaning that even if the LEDs were not sealed at all you could put the LEDs into the water and they would continue to work and nothing would happen. It is recommended that you use a GFCI safely plug, available at any aquarium, hardware, electrical or home improvement store, or online.
Comes with 3 ft (90 cm) of vinyl airline, but requires an air pump. A standard air pump will work, however a larger pump with two outlets combined into a single outlet is preferred. It is the air bubbles which move water into the growth compartment and up the growth surfaces, and also supply carbon dioxide (CO2 in the air) to the surfaces, which allow algae to grow in the filter. If you don't have a proper pump, you can use what you do have in the mean time. One pump which works well is the Fusion 700 from JW Pet, which we sell here:
The LEDs are four red (660 nm) 3-watt LEDs, which are double sealed in epoxy. Some red light does come out of the bottom holes, but most of the light is blocked by the special plate underneath the filter; so it will not make little red dots on the bottom of the aquarium or sump. You will need to get a timer so you can run the LEDs for up to 22 hours per day (not 24). The LEDs never needs replacing.
The DROP1.2x will need to be cleaned ("harvested") every 7 to 14 days or when thick with growth. Just lift up the DROP1.2x out of the water, open the hinged lid, and pull the algae out (freshwater use will usually require taking the filter to your sink). You can even feed some of the algae to your fish, and there will probably some some pods inside that you can feed too.
The DROP1.2x comes with a 6 month warranty: Warranty is for replacement or repair only; not a refund. Costs for shipping back to us are covered if you are in the U.S. Costs for shipping back to us are not covered if you are not in the U.S., however we will pay for shipping back to you. In either case, you will need to ship the entire unit back to us before we can ship a replacement. Warranty is limited to repair or replacement, and does not cover fish loss, personal injury, property loss, or direct, incidental or consequential damage arising from the use of it. The warranty and remedies set forth above are exclusive and in lieu of all others, whether oral or written, express or implied. We specifically disclaim any and all implied warranties, including but not limited to lost profits, downtime, goodwill, damage to or replacement of other equipment and property, and any costs of recovering animals, plants, tanks or other aquarium related items and/or equipment. We are not responsible for special, incidental, or consequential damages resulting from any breach of warranty, or replacement of equipment or property, or any costs of recovering or reproducing any equipment, animals or plants used or grown with this product.
Can be shipped to any country; you can find shipping costs by using the shopping cart; be sure to click "display rates". If you don't have a zip code, enter "zip code" instead. Note that shipping outside of the USA might require you to also pay an import charge when it arrives. We cannot mark it as "gift", however. The lowest cost overseas shipping is generally USPS First Class Mail International, however this option does not offer tracking outside the U.S. So a better option is USPS Priority Mail, which offers both tracking and insurance. The size of the shipping box 10" x 7" x 5" (25 cm x 18 cm x 15 cm).
DROP1.2x size: 3.25" wide x 6" tall x 2.75" thick front-to-back (8 cm wide x 15 cm tall x 7 cm thick). It requires at least 5" (13 cm) of water to operate in.
DROP1.2x on freshwater by Amwassil on the scrubber site: